WARNING: If the information in these instructions are not followed exactly, a fire orexplosion may result causing property damage, personal injury or
Heater DimensionsPipe Connections& LocationsCondensing Pool Heater 7 22/12/08Fig. 3.1DimensionsModel ABC Genie 35138mm 229mm 361mm G
Outdoor TerminalDimensionsCondensing Pool Heater 8 22/12/08Fig. 3.3Outdoor Flue Terminal(MBOT)Fig. 3.4Clamp Assembly ScrewPitched RoofIn
Condensing Pool Heater 9 22/12/08Flue ExamplesFlue Kit Part CodesType of Flue SystemKit Code Description Outdoor Kit Horizontal Terminal
Condensing Pool Heater 10 22/12/08Flue Kit Part Codes (cont.)Kit Code Description FEL Photo of KitMBHT Horizontal Wall Terminal 3.9mMBHV
Condensing Pool Heater 11 22/12/081. Ensure the required service clearance isavailable.2. Fit the 90 degree elbow to the heater andmeasu
Conversion to LPGThe Heater can be converted on site. NG to Pro-pane, or Propane to Butane.1. With the Gas and Electrical supply off, undothe three sc
Condensing Pool Heater 13 22/12/08Condensate ConnectionThe direction of the plastic condensate drain pipeconnection can be altered from
Example Condensate Disposal MethodsCondensateDrain fromHeaterCondensate PressureSwitch PipeConnectionConnect ToWaste(Option toexit Heaterleft or right
Condensing Pool Heater 15 22/12/08Fig. 8.2CommissioningGeneralIMPORTANT The heater primary contains Senti-nel X500 inhibitor/anti-free
Condensing Pool Heater 16 22/12/08User Setup ModeSwitch on with the panel switch whilst pressing the Lock/Reset button. then releas
PERFORMANCE SPECIFICATIONS GAS CATEGORY, TYPE AND SUPPLY PRESSUREII2H3PG20 @ 20 mbarG31 @ 37 mbar NATURAL GAS PROPANEMODEL MB35S MB50S MB35S MB50SC
Kit Part Codes:2 Heaters: MBMIK23 Heaters: MBMIK34 Heaters: MBMIK45 Heaters: MBMIK56 Heaters: MBMIK67 Heaters: MBMIK78 Heaters: MBMIK8Multiple Heater
Operation Turn on all the Heaters with their Pool Temperature Controls. The Master will show temperatures and the Slaves“---”. Set the required tem
Wall Mounting KitCondensing Pool Heater 19 22/12/08Fig. 10.4Fig. 10.347637694017046HEATEROUTLINETOP WALLMOUNTINGBRACKETHORIZONTALWALLTE
Condensing Pool Heater 20 22/12/08Fig. 10.5BOTTOM WALL MOUNTING BRAKETREMOVE DEMOUNTABLEPOOL FITTINGS FOR BETTERDRILL ACCESSTOP WALLMO
Fig.11.0Condensing Pool Heater 21 22/12/08Schematic Wiring
WARNING: BEFORE COMMENCING OR COMPLETING ANY ELECTRICAL WORK ON THE APPLIANCE, ITIS RECOMMENDED THAT THE BASIC SAFETY CHECKS FOR EARTH CONTINUITY, SHO
Fault CodesCondensing Pool Heater 23 22/12/08DISPLAYLOCK / RESETGREENYELLOWREDLED1REDREDLED2Running, raising pool temperature to 28°CUp t
Fault CodesCondensing Pool Heater 24 22/12/08DISPLAYLOCK / RESETGREENYELLOWREDLED1REDREDLED2FRONT PANELON PCBEXPLANATION‘P’ alternating w
SERVICINGHealth and Safety Statement :This Heater contains no asbestos.Routine ServiceTo ensure continued efficient operation of theappliance it is r
Heat Exchanger Combustion Temperature Sensor. Flue Thermostat Ignition Control. Gas Valve. Fan. Pump. Heat Exchanger. Secondary Heat Exchange
TECHNICAL DATA Inside coverUser Instructions 1INTRODUCTION 3Heater Location 3Gas Supply 4Conversion 4Flueing 4Air Supply 4Outdoor Heaters 4Condensate
Condensing Pool Heater 27 22/12/08Gas Valve (See Fig.14.3) Remove the Ignition Control, see above. Release the Gascock by undoing th
SparesItem Mfg’ Part Number Supplier Part NoPrimary Heat Exchanger (Genie35) M2136 SPMBG001Primary Heat Exchanger (Genie 50) M2139 SPMBG002Seconda
Fig.14.6Heater ComponentsCondensing Pool Heater 29 22/12/08Fig.14.0Fig.14.1Fig.14.4Fig.14.3Fig.14.2Flue ThermostatHeat ExchangerCombust
INSTALLATION & SERVICE HISTORYModel Gas Genie 35 Genie 50 NG LPGDateCleaned ?PressureCOCO2Service HistoryCommissioningInstaller Corgi No Date:Wor
Before Start UpKeep heater area clear and free from combustibles,flammable liquids and chemicals.Pool water must be flowing through the Heater and th
Condensing Pool Heater 2 22/12/08Pool Demand LED - GreenOff - There is no Pool Heating demand, pool heatingis off.On - There is Pool He
Health and Safety document No 635, “Electricity atWork Regulations”.Detailed recommendations are contained in thefollowing British Standard Codes of P
Terminal Position MinimumBelow window or vent 300 mmBelow gutter or pipes 75 mmBelow eaves 200 mmBelow balcony or roof 200 mmFrom a window 200 mmFrom
Genie Resistance0.00.20.40.60.81.01.21.41.60 50 100 150 200 250l/mm headWinterisationTurn off the Mains electricty and Gas Supply.As supplied the Heat
INSTALLATION OF HEATERSpace Required for Installation and Service.Left, Right or Above 300 mm 12 in.In Front 800 mm 40 in.Suggested procedure:Sit
Comentários a estes Manuais